Riser

Thomson's Carbon MTB bars are made with three different fiber types for strength, durability and long times in the saddle. Thomson's MTB Carbon Cross Country Handlebar is a flat bar with an off center clamp area allowing a flat riding position and reversible for a 5mm drop. It also has 8° of backsweep for comfort and 730mm in width for plenty of leverage. The bars are made with three different fiber types with different tensile strength and tensile modulus, including high strength carbon fibers. This helps to allocate stiffness and flex where needed. The bars are molded with an EPS mandrel inside to avoid wrinkles inside the layup during molding. Most other bars are molded over inflated nylon bladders. All carbon fiber material is produced by Toray and uses tailor made nano Epoxy Resin for very high impact resistance. Toray is the main supplier of carbon fiber to Boeing and Airbus. 1.5K woven impact ends help prevent damage to unidirectional fibers from shortening the bar or impact with the ground. With a light weight and precision tolerance clamp sections, it’s the best bar for your Thomson X4 stem. It’s also certified to EN, tested to DIN+. Friction Paste recommended for installation

Race Face's Chester bar is made of tough 6061 alloy with the perfect width, sweep and rise to be at home on both your DH and hardtail rigs. These bars will last long after your bones, bruises and scrapes heal up and you’re ready to tackle that gap jump that has had your number. Features - Manufactured from cold drawn, seamless 6061 Alloy. - Butted for an optimal strength to weight ratio. - Wider construction & re-designed taper offers - 740mm wide - 9° rearward, 6° upward

Wider than Turbine but still sporting the agressive sweep design putting you in the perfect riding position, these bars come in a variety of rises to allow you to fine tune your cockpit and dial in your setup. Tried and tested 7075 aluminum gives you the confidence for agressive all-mountain riding and 35mm technology for fantastic overall weight/strength ratio. Your six inch travel bike will thank you. - Manufactured from cold drawn, 7075 Aluminium - 35 optimized triple butted design - Turned up to Rally control with 800mm width - Rise sizes to for every build and preference 10/20/35mm - Stealth black on black decals to match every frame color

The No.9 35.0 Mountain Carbon Handlebar is designed and built for the most extreme trail and all-mountain riding. The oversized stem clamp adds to front-end stiffness for precise input, while the carbon construction provides vibration damping in a lightweight and durable package. - Unidirectional carbon fiber construction - 35mm stem clamp - 8 degrees of backsweep with 5 degrees of upsweep - Trimmable ends, made easy with graphic markings - Rated to ASTM Condition 4 for extreme off-road riding

Occupying a class all its own, our Winston Handlebar is a performance carbon mustache bar loaded with versatility and flare. Featuring a 25mm rise and 73-degree backsweep, it offers compatibility with road, mountain, and bar-end controls. Pretty enough to punch up commuter rigs and sport touring bikes alike, it's built tough to handle everything from rough, off-road conditions to long rides in the country. Comfortable in both the drop and riser positions, the unique and multi-functional Winston is sure to inspire upgrades and eye-catching custom builds. - Compatible with road, mountain, and bar-end controls - Tested to ASTM 3 - 90mm clamping area to fit Salsa Anything Cradle - Can be ridden in up or down position - Unidirectional carbon fiber construction - Weight: 250g

TruVativ's super-tough Hussefelt Riserbar is made from triple-butted AL-66 for a long fatigue life and great strength. The wide bar and high rise gives you an upright position for greater control in technical sections and confidence on steep descents.

TruVativ's Stylo T20 Flatbar is made from butted aluminum for low weight and high strength. At 600mm wide, it gives you a nice XC width without weighing you down. A subtle sweep gives your hands the perfect position for greater control in technical sections.

TruVativ's Stylo T30 Riserbar will have you taking on climbs and descents like a champ. This butted aluminum bar is 700mm wide, to give you enough leverage to muscle your rig without weighing you down. And, the multiple rise options let you choose the perfect upright position for greater control in technical sections.

Thomson's Carbon MTB bars are made with three different fiber types for strength, durability and long times in the saddle. The MTB Carbon Trail Handlebar is built for strength with enough flex built in for all day comfort. It’s strong enough for all mountain/trail riding and light enough for racing. The bars are made with three different fiber types with different tensile strength and tensile modulus, including high strength carbon fibers. This helps to allocate stiffness and flex where needed. The bars are molded with an EPS mandrel inside to avoid wrinkles inside the layup during molding. Most other bars are molded over inflated nylon bladders. All carbon fiber material is produced by Toray and uses tailor made nano Epoxy Resin for very high impact resistance. Toray is the main supplier of carbon fiber to Boeing and Airbus. 1.5K woven impact ends help prevent damage to unidirectional fibers from shortening the bar or impact with the ground. With a light weight and precision tolerance clamp sections, it’s the best bar for your Thomson X4 stem. It’s also certified to EN, tested to DIN+. Friction Paste recommended for installation

The Terminal Bar blends cruiser-style comfort with off-road touring performance. Able to run with a 40mm drop or rise, its swept-back design makes it great for long rides on rough, technical terrain. - 22.2mm diameter grip area; good to go for MTB shifters, brake levers, and grips - 34 degree backsweep with a 40mm + / - rise

Chrome plated long-horn style design.

Sturdy steel construction with a versatile riser bar style.

World Cup quality performance, developed with the pros. SPANK Industries' legendary SPIKE 800 Race handlebar is the 5th generation of the SPIKE Race handlebar legacy, developed in coordination with some of the world’s top DH and Enduro pros. A unique construction of Super 6 alloy, processed with SPANK’s patented CNC bending and Dual-Extreme-Gradual Taper (XGT) technology makes the SPIKE 800 Race handlebar a stronger, safer, performance-optimized component for the weight-conscious gravity rider. The race-tuned geometry and competitive weight make this bar the perfect solution for AM/Enduro to Downhill Race. SPANK's SPIKE 800 Race is the handlebar of choice for Nicholi Rogatkin, Thomas Genon, Tomas Zejda and many more. - Key technologies: Dual XGT, CNC Bending, Impact Ends, MGR, Super 6 Alloy - Material: MGR Super Six Alloy - Weight: ±300g (5mm) / ±310g (15mm) / ±320g (30mm) / ±330g (50mm) - Diameter: 31.8mm - Rise: 5mm / 15mm / 30mm / 50mm - Length: 800mm (Adjustable to 740mm) - Geometry: 4° up x 8° back - Finish: Shotpeen anodized, decal logos

- DH Race tuned award winning alloy handlebar design, developed with World Cup professionals - Injected proprietary foam Vibrocore provides vibration damping to reduce arm pump and hand-numbness - Increased strength and stiffness compared to conventional alloy bars - Shot-peening and anodizing enhances fatigue life even further - Adjustable to 740mm - KEY TECHNOLOGIES: Vibrocore, Dual XGT, CNC Bending, Impact Ends, MGR Super 6 Alloy - MATERIAL: MGR Super 6 Alloy - WEIGHT (g): ±340 (15mm) / ± 350 (30mm) / ±360 (50mm) - DIAMETER (mm): 31,8 - RISE (mm): 15 / 30 / 50 - LENGTH (mm): 800 (adjustable to 740) - GEOMETRY (deg°): 4° up x 8° back - FINISH: Shot peen anodized, decal logos

Your favorite bars just got bigger, wider, and lighter, Go figure? The magic of 35—believe the hype! Increasing the bar diameter to 35mm allowed Race Face to shave material from the bar resulting in a dramatic reduction in overall weight while retaining the proven stiffness, strength and performance Race Face bars are known for. The ATLAS 35 bar also expands to an 800mm width (Can be trimmed down to 750mm) for hyperspeed control, can you handle it? - Proven design and durability of the Race Face Atlas bar, with increased stiffness and reduced weight of the 35mm bar platform - Requires 35mm bar clamp diameter stem - Full 800mm width that can be trimmed down to a minimum 750mm - 8 degree rearward sweep, 5 degree upward sweep

Race Face Atlas riser handlebar with an anodized, shot-peened finish. - Aonodized, shot-peened finish - Cold-drawn and butted proprietary AirAlloy aluminum tubing - 4 degree upsweep

- Intended for Cross Country and Trail use - 1/4 Risers have a 2deg upsweep - Unidirectional carbon fiber with reinforced stem anti-crush zone - Bar Clamp Diameter: 31.8 mm - Bar Rise: 5 mm - Bend: 8 deg - Weight: 175 g

- Intended for Cross Country and Trail use - 1/4 Risers have a 2deg upsweep; 3/4 Risers have a 4deg upsweep - Unidirectional carbon fiber with reinforced stem anti-crush zone - Bar Clamp Diameter: 31.8 mm - Bar Rise: 20 mm - Bend: 8 deg - Weight: 175 g - Width: 725 mm

- Intended use: XC and Trail - Proven design and durability of the Race Face Next SL bar with increased stiffness and lighter weight of the 35mm platform - Manufactured from UD Carbon with matte clearcoat - Requires 35mm bar clamp diameter stem - 8 degree rearward sweep, 5 degree upward sweep

The Next R handlebar features 800mm of premium unidirectional carbon with the shred-ready positioning of Race Face's SixC bars. DH strength and Enduro weight for when you really need to lean into it. - Manufactured from UD Carbon with matte clearcoat - Carbon optimized flex for improved small bump compliance - 35mm bar diameter for incredible strength/weight ratio

Race Face set an industry benchmark with the its Sixc product group - light and strong carbon DH rated crank and bar. Building on the unprecedented success of their proprietary Carbon Technology program, SIXC rewrites the rules in the 6-8 inch travel bike world. SIXC (the C is silent, eh!) represents the culmination of years of Race Face engineering in both carbon and all mountain products. Race Face has created a bar for the aggressive rider who demands the ultimate in performance. Strong enough for DH, yet light enough to not hold you back on the pedal up to that new trail you have been hearing so much about, SIXC blows up the limits of carbon performance. - SIXC bars are manufactured with a leading edge composite material which allows us to reach our high strength requirements at an impressively low weight - Minimum bar width of 28" or 710mm at indicated cut marks - Reinforced clamping zones for lock-on grip - Daily destructive testing from each production run ensures each bar meets the exacting standards set by our engineers

- AL7050-T6 tubular alloy construction - 35mm oversized clamp diameter - 800mm width - 7°/8° back sweep (Depending on rise dimension) - 5° upsweep - ISO-Mountain safety certified - 290-335g (Depending on rise dimension)

- AL7050-T6 tubular alloy construction - 35mm oversized clamp diameter - 800mm width - 7°/8° back sweep (Depending on rise dimension) - 5° upsweep - ISO-Mountain safety certified - 290-335g (Depending on rise dimension)

- AL7050-T6 tubular alloy construction - 35mm oversized clamp diameter - 800mm width - 7°/8° back sweep (Depending on rise dimension) - 5° upsweep - ISO-Mountain safety certified - 290-335g (Depending on rise dimension)

- AL6066-T6 tubular alloy construction - 35mm oversized clamp diameter - 800mm width - 7°/8° back sweep (Depending on rise dimension) - 5° upsweep - ISO-Mountain safety certified - 290-335g (Depending on rise dimension)

- AL6066-T6 tubular alloy construction - 35mm oversized clamp diameter - 800mm width - 7°/8° back sweep (Depending on rise dimension) - 5° upsweep - ISO-Mountain safety certified - 290-335g (Depending on rise dimension)

Origin-8's Space Off Road II Handlebar is ready to explore the final trail frontier. This radical bar is crafted from lightweight aluminum and features a 50mm sweep and 37.5mm rise. But it's not just for looks — it lets you distribute your weight and hand placement in multiple ways for more control and comfort.

A race-proven handlebar, the M9 bar is ENVE's dedicated downhill option. Designed around a 31.8mm clamp diameter and a downhill-focused flex profile, this bar’s celebrated ride feel defined the potential of a DH carbon fiber bar and realigned performance expectations. The M9 bar features 8-degree backsweep and 4-degree upsweep. - Material: Carbon - Weight: 245g (30mm rise); 265g (50mm rise) - Bar Width (Max): 810mm - Bar Width (Min): 780mm - Clamp Diameter: 31.8mm - Backsweep: 8 Degrees - Upsweep: 4 Degrees - Torque Spec: Face Plate: 5.5Nm - Torque Spec: Controls: 5.5Nm

An quick way to make a bike more comfortable, Dimension High-bars come in four different rises for inexpensive and easy bar-height changes. - Four rise options available from 30-100mm - AL-6061 aluminum alloy - ISO4210 Safety Tested for City/Trekking use - Not recommended for use with bar-ends or clip-on aero bars - 15-degree sweep

The handlebar of choice for the Scott / Velosolutions and Norco Factory Racing World Cup teams, the BLACKLABEL 800 is the evolution of over a decade of DEITY handlebar development. By widening the center bore area, we could increase strength while still delivering an incredibly comfortable, stable, and responsive feel that is unmatched. This premium race good is built for championships! - 800mm width - Designed for DH / Enduro / All MTN applications - Dirt Mag Top 100 Product - 4 years running for 2014, 2015, 2016, and 2018 - Incredibly detailed two-tone bead blast and polished ano finish - 9-degree bend / backsweep by 5-degree upsweep - Custom butted 7075 T73 aluminum utilizing our proprietary Gradient Butting Technology - Designed for maximum ride quality with a 31.8mm bore - World Cup DH / Redbull Rampage / Crankworx and FMB World Tour proven - The handlebar of choice for the Scott / Velosolutions and Norco Factory Racing World Cup teams - Features measured cut marks and center alignment detail - Covered by our Lifetime Crash Replacement Policy to the original owner - 15mm rise: 333g - 25mm rise: 342g - 38mm rise: 343g