Skip to main content

Filter By:

  • Show More Brands

  • Show Fewer Brands
  • Show More Sizes
  • Show Fewer Sizes
  • Show More Model Years
  • Show Fewer Model Years

Tools

$8.95
Park's Bottom Bracket/Cassette Tool for Campagnolo is an indispensable tool for your Campagnolo drivetrain. It's for installing and removing all Record, Chorus, Centaur and Athena bottom brackets, and all Campagnolo cassette lockrings.
A dirty drivetrain causes poor shifting and unnecessary wear to expensive parts. The Chain Gang contains everything needed to quickly and easily clean the chain, freewheel cogs, and chainrings. The Chain Gang includes: - CM-5.3 Cyclone Chain Scrubber - GSC-1 GearClean Brush - 8 oz. bottle of Bio ChainBrite The CG-2.4 works on nearly any bike, including multi-speed, single-speed, and e-bikes.
• 12” Tungsten steel hacksaw blade specially designed to smoothly cut carbon composite handlebars, forks, seat masts, seat posts, etc. • Fits Park Tool SAW-1 Hacksaw and most 12” hacksaws • The CSB-1 is designed for use with the SG-8 Saw Guide. NOTE: Similar to a grinding stone, do not use this blade on aluminum
Heat-treated alloy tool steel, one inch base fits wrench or bench vise. Thin-wall construction allows use without removal of cones and locknuts. The FR-5 has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, Sunrace, Suntour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also fits Shimano disc brake lockrings - Always use a quick-release skewer to hold the tool in place and snug to cogs when loosening; for solid axles, use the axle nut
The Park Tool FR-5.2GT is designed specifically for use when removing and installing cassette lockrings from thru axle hubs. -Utilizes a 12mm guide pin to stabilize the tool during use - Fits 12-spline cassette lockrings from Shimano, SRAM (including 1x), SunRace, SunTour, Chris King and others (23.5mm diameter) - Fits some Shimano and similar disc brake rotor lockrings
$10.95
Heat treated alloy tool steel, one inch base fits wrench or bench vise. Thin wall construction allows use without removal of cones and locknuts. The FR-5.2G has 12 splines that are approximately 23.4mm across. - Fits Shimano, SRAM, SunRace, SunTour, Chris King and other cassette lockrings - Fits the SRAM XX1 11-speed cassettes - Also Fits Shimano disc brake lockrings - Guide pin stabilizes tool
$15.95
Park's Compact Crank Puller is used to remove Shimano Octalink, ISIS Drive and square-taper cranksets. It includes 2 rotating tips (16.3 and 11.3mm) to make the job easy. This is a great tool for your travel and home tool kit.
$19.95
Park's Crank Puller is for removing crankarms on Shimano's splined, oversize, pipe-billet bottom brackets. It employs a long handle and a fine thread for the leverage and torque needed to remove tight arms. Park's unique rotating tip ensures smooth operation and long life. (The CCP-44 does not fit standard square or tapered bottom brackets.)
A favorite of shop mechanics for over 30 year's, Park's CCP-22 Crank Puller removes crankarms that feature square tapers, and those that fit on Power Drive and Power Spline bottom bracket interfaces. The long, comfortable, built-in handle and fine thread provide the leverage needed to remove even the tightest crankarms. And, there's a rotating tip to ensure smooth operation and long life.
$15.95
Now you can easily tackle any crank bolt with Park's Crank Wrench. It features a dual-sided head with a 14mm socket and 8mm Allen wrench on a long, vinyl-coated handle so you're sure to have the leverage necessary for the job.
$20.95
The Park FR-6 Freewheel Remover fits most 4-notch BMX and singlespeed freewheels. It can be held with a wrench or vise and its narrow profile allows use without removal of cones and locknuts.
Park's FR-8 Freewheel Remover fits flip-flop BMX hubs with 30 x 1mm threads. It can be held with a wrench or vise, and its narrow profile allows use without removal of cones and locknuts.
A sturdy bicycle cleaning brush with a unique angled and contoured shape – perfect for cleaning cassettes and freewheels as well as tires. With a strong ergonomic handle and stiff nylon bristles, the GSC-4 scrubs away the toughest muck and mess.
$5.95
Park's Gear Clean Brush has a handle on one end with a curved, serrated edge perfect for cleaning between cassette cogs. The other end's tough nylon bristles are ideal for cleaning the derailleurs, chain and other drivetrain parts to keep them clean and prevent premature wear. It also works great on brakes and other components that collect dirt and grime. The GearClean easily fits in a toolbox or pack.
Get those heads sealing like new and reduce compressor energy waste with Park Tool's Head Seal Kit. This kit will help get rid of that hissing sound you've been hearing when it has been too long since servicing your Park Tool INF-1 or INF-2 shop inflator. Kit includes: - 1 #1586 Presta Seal - 1 #1588 Schrader Seal - 2 #1576-2 O-rings for Shuttle-valve - 1 #1682-2 O-ring for INF-1 and INF-2 Head Adaptors
Park's AWS-7 features a Y-shaped nylon handle with 4 and 5mm Allen wrenches and a T25 Torx wrench. This convenient 3-in-1 tool keeps commonly used wrenches together and offers an excellent grip as well.
Park's Home Mechanic Pedal Wrench is great for your home workshop and event tool box. This top-quality 15mm pedal wrench provides the leverage you need to remove stubborn pedals. It's made to last from heat-treated steel, and the handle has a vinyl grip for comfort.
The strong, lightweight IB-2 features ten essential tools in the compact form factor of our unique I-Beam handle. Perfect for on-the-ride adjustment of brakes, handlebars, saddles, or derailleurs. With its compact size, the IB-2 is a perfect tool for the saddlebag, jersey pocket, or toolbox.
$72.95
"Take the guesswork out of internal routing. The IR-1.3 speeds the installation of internally-routed cable, housing, electronic wiring and hydraulic hose into carbon fiber, titanium, and aluminum frames. The straightforward guide magnet system utilizes five long guide cables with unique fittings, which can be routed through the frame in a number of ways using the included guide magnet. Everything is neatly stored in a convenient compact case. A true time and frustration saver!??Includes five 188 cm (74"") guide cables with attached magnets and unique fittings: • Barbed adapter — Threads into the end of brake & shift cable housing as well as hydraulic brake hose • Rubber adapter — Securely holds electronic shifting wire such as Shimano® Di2, SRAM® RED® eTAP®, FSA® K-Force® WE®, and Campagnolo® EPS • Di2®-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® shift wire, and is perfectly sized to fit into frame holes as small as 6 mm • Di2® EW-SD300-specific adapter — Specially-designed connector clips into the end of Shimano® E-tube® Di2® EW-SD300 shift wire • Reverse-polarity magnet — Used in conjunction with any of the other guide cables - feeds into the opposite end and meets the leading cable in the middle, aiding in routing on frames with tricky interior shapes Also included: • Double-threaded barb — Securely attaches new housing or hydraulic hose to existing housing or hose, allowing for easy replacement without redoing the routing • Guide magnet — routes guide cables through the frame from the outside"
$16.95
Many chains use a master link that allows the chain to be installed and removed by hand. While master links don't require traditional chain tools, over time, dirt and corrosion can make it difficult to separate them by hand. Park's Master Link Pliers make removing and installing these master links quick and easy. Simply insert the specially sized jaws into the link and squeeze the vinyl-coated handles!
$7.95 - $13.95
World-famous Park Tool quality wrapped up in a great set of metric combination wrenches. Forged from chrome vanadium steel, chrome plated, meticulously polished, then center dipped in Park Tool blue vinyl for a positive grip.
Park's Mini Chain Brute Chain Tool goes anywhere and features a V-shaped handle, a super-strong replaceable pin, and fine threads to make chain removal and installation a breeze. The CT-5 works on any derailleur chain, including Shimano Hyperglide and 9-, 10-, and 11-speed. It works for loosening tight links, too.
$43.95
Park’s Professional Cable And Housing Cutter is specifically for use on derailleur and brake cables and housing. It even makes quick work of hard-to-cut shift-cable housing. Its cold-forged, heat-treated-steel handles won't bend and its precision-ground jaws cut perfectly every time. Its dual-density molded grips are specially contoured for superior comfort and control. Plus, there’s a built-in cable-end crimper and a forming hole for reforming housing ends.
Park's Professional Pedal Wrench features an angled, oversize head for maximum leverage. It has two 15mm wrenches at different angles, so you can maximize your leverage, and a long, round, vinyl-coated handle that won’t dig into your hand the way flat wrenches do. There's even a hole in the end for hanging the wrench on your toolboard.
$114.00
With today’s lightweight components, torque wrench use in the shop is no longer an option — it’s a must for every mechanic. The Park Tool TW-5.2 is a high-quality, ratcheting, click-type torque wrench that accurately measures and applies the proper amount of torque to a component’s threaded fastener(s). With a range of 2-14Nm, the TW-5.2 is designed for the lower torque settings that a shop or consumer would use for proper seat post, seat clamp and handlebar / stem applications. Comes with its own protective case.
$1.20 - $2.74
Park Tool's Replacement Chain Tool Pin (2-Pack) fits Park Tool's CT-1, CT-2, CT-3, CT-3.2, CT-5, and CT-7 Chain Tools. • Made from hardened alloy tool steel • Uses 7mm or 9/32" 12 pt box end/socket • Sold singly or in pairs
Park Tool's Replacement Chain Tool Pin fits Park Tool's CT-6, CT-6.2, and CT-6.3 Chain Tools (each sold separately). • Made from hardened alloy tool steel • NOTE: The 985-1 will also push out the chain rivet completely from the chain side plate.
$35.95
Updated to fit current 12-speed cassettes, this combination chain whip and freewheel / lockring remover wrench is heat treated to prevent bending, flexing and wear and features a long, molded handle in addition to a built in hex shaped driver. - Works on 5- to 12-speed road and mountain bike cassettes and freewheels - 1-inch (25.4mm) box-end wrench fits Park Tool Freewheel / Cassette Lockring Tools - Features hardened pins to keep the chain in place
The BBT-16 removes and installs the self-extracting/one-key release caps on SRAM and RaceFace cranks with a 16mm hex hole. Features investment cast steel construction and an option to use 8mm hex for better leverage.
$9.95 - $9.99
Park's Cone Wrenches are made of durable tool steel and are nice and thin to fit on the small-clearance cones found on hubs and other bearing assemblies. Plus, they work as regular wrenches, too. They feature Park's special Y heads that put more material where it's needed for excellent durability and strength. Most applications require at least 2 cone wrenches. If you have questions please contact us and we can recommend the correct sizes for your needs.
Page 1 of 11 Next page